使用WPA2加密后,无线计算机启动后很快就会停止工作

我的电脑出现了一个奇怪的问题,我的电脑启动后我的wifi停止工作了一段时间。 让它再次运行的唯一方法是重新启动计算机。 我知道问题不在于任何硬件,因为它与Windows 10 I双启动完美配合。

系统信息

Manufacturer: Lenovo Model: G50-70 OS: 64-bit Ubuntu 14.04 LTS Kernel: 3.16.0-46-generic 

此问题也发生在:

 OS: 64-bit Ubuntu 15.04 Kernel: 3.18.21-031821-generic 

网络控制器信息:

  *-network description: Ethernet interface product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 28:d2:44:e1:6f:15 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.040.00-NAPI duplex=half latency=0 link=no multicast=yes port=twisted pair speed=10Mbit/s resources: irq:43 ioport:4000(size=256) memory:c0504000-c0504fff memory:c0500000-c0503fff *-network description: Wireless interface product: RTL8723BE PCIe Wireless Network Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 38:b1:db:7c:18:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8723be driverversion=3.18.21-031821-generic firmware=N/A ip=192.168.0.66 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:19 ioport:3000(size=256) memory:c0400000-c0403fff 

如果您需要其他信息,请发表任何评论。

更新:

将路由器切换到WEP加密似乎可以解决问题。 但是,WEP是不安全的,所以如果找到不同的修复程序,将不胜感激。

更新:

这个问题也出现在Ubuntu 15.10中。 但是,您可以简单地断开连接然后重新连接,以便暂时解决问题。 2分钟到2小时后,问题再次发生。

类似问题:

互联网随机停止工作,但重启后重新开始工作
在Realtek RTL8187SE上,无线网络每隔几分钟就会切断一次

试试这个并重启:

 echo "options rtl8723be fwlps=N ips=N" | sudo tee /etc/modprobe.d/rtl8723be.conf 

这将禁用卡的一些电源管理,通常会有所帮助。

您可以通过安装其他驱动程序来修复它。 在终端运行

 sudo add-apt-repository ppa:hanipouspilot/rtlwifi sudo apt-get update sudo apt-get install rtlwifi-new-dkms linux-firmware 

并重新启动。