让Killer Wireless-AC 1535正常工作以安装Ubuntu 16.04

我的无线设备是168c:003e:1a56:1353 rev 32.安装程序包含一个4.4.0-21-lowlatency内核,我在/lib/firmware/ath10k/QCA6174/hw3.0看到固件文件有一块board.binfirmware-4.bin 。 这些是股票文件。 在dmesg我看到初始化失败了,这是真的,我甚至没有在ifconfig看到设备。 在初始化期间,它正在寻找firmware-5.bin ,它不在那里。

首先,我尝试在这里添加固件-5 .bin: https : //github.com/kvalo/ath10k-firmware/pull/4/files

那没有帮助,文件中的魔法不匹配。 我想这是为4.2或其他东西煮熟的。 然后我尝试使用official中的所有文件https://github.com/kvalo/ath10k-firmware/tree/master/QCA6174/hw3.0 (由http://www.killernetworking.com/推荐) 支持/知识库/ 17-linux / 20-killer-wireless-ac-in-linux-ubuntu-debian )。 魔术不匹配。

由于我在安装的开始,重启不是我的选择,这是一个22捕获。 相反,我写了一个小脚本modprobe -r s ath10k_pciath10k_coreathmac80211cfg80211 。 另一个脚本以相反的顺序insmod

我也通过https://github.com/kvalo/ath10k-firmware/pull/3尝试了board-2.bin。 魔术不匹配。


更多信息。 安装程序的/lib/firmware/ath10k/QCA6174/hw3.0固件目录的初始/原始状态:

 -rw-r--r-- 1 root root 8124 Mar 21 12:27 board.bin -rw-r--r-- 1 root root 733784 Mar 21 12:27 firmware-4.bin cb37c63d9ca28f53fea1ff09ad7c7a82 board.bin a5dfbc03c9a7a73f7aa8d0a94a6d9426 firmware-4.bin 

这导致:

 [ 118.170694] ath10k_pci 0000:04:00.0: enabling device (0000 -> 0002) [ 118.171818] ath10k_pci 0000:04:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0 [ 118.658737] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/cal-pci-0000:04:00.0.bin failed with error -2 [ 118.658754] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2 [ 118.658770] ath10k_pci 0000:04:00.0: could not fetch firmware file 'ath10k/QCA6174/hw3.0/firmware-5.bin': -2 ... [ 128.810919] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/board-2.bin failed with error -2 [ 131.928674] ath10k_pci 0000:04:00.0: qca6174 hw3.2 (0x05030000, 0x00340aff sub 1a56:1535) fw WLAN.RM.2.0-00180-QCARMSWPZ-1 fwapi 4 bdapi 1 htt-ver 3.26 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1 features wowlan,ignore-otp,no-4addr-pad [ 131.928676] ath10k_pci 0000:04:00.0: debug 0 debugfs 1 tracing 1 dfs 0 testmode 0 [ 134.928910] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 134.982552] ath: EEPROM regdomain: 0x6c [ 134.982553] ath: EEPROM indicates we should expect a direct regpair map [ 134.982554] ath: Country alpha2 being used: 00 [ 134.982555] ath: Regpair used: 0x6c [ 136.139717] ath10k_pci 0000:04:00.0 wlp4s0: renamed from wlan0 [ 147.251066] IPv6: ADDRCONF(NETDEV_UP): wlp4s0: link is not ready [ 152.475059] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 158.475164] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 158.532546] IPv6: ADDRCONF(NETDEV_UP): enp6s0: link is not ready [ 158.533313] IPv6: ADDRCONF(NETDEV_UP): enp6s0: link is not ready [ 167.547281] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 173.547366] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 178.826678] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 184.826637] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 202.258851] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 208.258910] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 213.537200] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 219.537070] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 235.258295] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 241.258474] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 246.537511] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 252.537681] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 268.259942] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 274.259976] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 279.538073] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 285.538232] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 301.260390] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 307.260552] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 312.538796] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 318.539935] ath10k_pci 0000:04:00.0: could not suspend target (-11) ... [ 340.262113] ath10k_pci 0000:04:00.0: could not suspend target (-11) [ 345.540330] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11 [ 351.540341] ath10k_pci 0000:04:00.0: could not suspend target (-11) 

我的一个尝试看起来很有希望dmesg没有固件崩溃,但无法初始化核心:

 -rw-r--r-- 1 root root 42110 Jul 3 09:56 board-2.bin -rw-r--r-- 1 root root 8124 Jul 3 09:56 board.bin -rw-r--r-- 1 root root 733784 Mar 21 12:27 firmware-4.bin -rw-r--r-- 1 root root 572324 Jul 3 09:57 firmware-5.bin 5e47d7cbe6255e4ac3ef71f6e2210f95 board-2.bin 1d07f60b4f6e3dc06028f4f31d1eec60 board.bin a5dfbc03c9a7a73f7aa8d0a94a6d9426 firmware-4.bin 2c5629dc360ee3606c12088ee5e2de98 firmware-5.bin [ 2798.276194] ath10k_pci 0000:04:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0 [ 2798.477454] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/cal-pci-0000:04:00.0.bin failed with error -2 [ 2798.539215] ath10k_pci 0000:04:00.0: found invalid board magic [ 2798.622537] ath10k_pci 0000:04:00.0: otp calibration failed: 3 [ 2798.622538] ath10k_pci 0000:04:00.0: failed to run otp: -22 [ 2798.622539] ath10k_pci 0000:04:00.0: could not init core (-22) [ 2798.622550] ath10k_pci 0000:04:00.0: could not probe fw (-22) [ 3318.953548] IPv6: ADDRCONF(NETDEV_UP): enp6s0: link is not ready [ 3318.954150] IPv6: ADDRCONF(NETDEV_UP): enp6s0: link is not ready 

大多数情况下,我在dmesg中遇到固件崩溃。 我很快就会尝试deb包。


注意:每次启动时检查BIOS是否未从UEFI-CSM模式恢复为UEFI非常重要。 显然这对于​​安装来说是至关重要的,没有CSM安装就会默默地停止。 还要检查BIOS是否还没有恢复到安全启动模式。 太头疼了!

将v1.157固件包升级到1.158有帮助(我不需要换掉1.158 deb中的任何文件)。 细节:

  1. 首先我停止了网络:

     sudo su /etc/init.d/Network-Manager stop /etc/init.d/Networking stop 
  2. 卸载内核模块:

     modprobe -r ath10k_pci modprobe -r ath10k_core modprobe -r ath modprobe -r mac80211 modprobe -r cfg80211 
  3. 升级了固件包

     dpkg -i linux-firmware_1.158_all.deb 

之后的固件目录的内容:

 -rw-r--r-- 1 root root 271412 May 6 12:42 board-2.bin -rw-r--r-- 1 root root 8124 Apr 25 12:59 board.bin -rw-r--r-- 1 root root 733784 Apr 25 12:59 firmware-4.bin ac5184615090503870442da5f703de25 /lib/firmware/ath10k/QCA6174/hw3.0/board-2.bin cb37c63d9ca28f53fea1ff09ad7c7a82 /lib/firmware/ath10k/QCA6174/hw3.0/board.bin a5dfbc03c9a7a73f7aa8d0a94a6d9426 /lib/firmware/ath10k/QCA6174/hw3.0/firmware-4.bin 

dmesg的:

 [ 1084.393020] ath10k_pci 0000:04:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0 [ 1084.594123] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/cal-pci-0000:04:00.0.bin failed with error -2 [ 1084.594143] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2 [ 1084.594149] ath10k_pci 0000:04:00.0: could not fetch firmware file 'ath10k/QCA6174/hw3.0/firmware-5.bin': -2 [ 1086.774542] ath10k_pci 0000:04:00.0: qca6174 hw3.2 (0x05030000, 0x00340aff sub 1a56:1535) fw WLAN.RM.2.0-00180-QCARMSWPZ-1 fwapi 4 bdapi 2 htt-ver 3.26 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1 features wowlan,ignore-otp,no-4addr-pad [ 1086.774545] ath10k_pci 0000:04:00.0: debug 0 debugfs 1 tracing 1 dfs 0 testmode 0 [ 1086.828603] ath: EEPROM regdomain: 0x6c [ 1086.828605] ath: EEPROM indicates we should expect a direct regpair map [ 1086.828606] ath: Country alpha2 being used: 00 [ 1086.828607] ath: Regpair used: 0x6c [ 1086.830651] ath10k_pci 0000:04:00.0 wlp4s0: renamed from wlan0 

所以我们终于有了wlan0 (改名为wlp4s0

  1. 加载了内核模块

     cd /lib/modules/4.4.0-21-lowlatency/kernel/ insmod net/wireless/cfg80211.ko insmod net/mac80211/mac80211.ko insmod drivers/net/wireless/ath/ath.ko insmod drivers/net/wireless/ath/ath10k/ath10k_core.ko insmod drivers/net/wireless/ath/ath10k/ath10k_pci.ko 
  2. 开始联网

     /etc/init.d/Networking start /etc/init.d/Network-Manager start 
  3. 需要重启nm-applet

     kilall nm-applet nohup nm-applet & 

现在我可以安装mdadm 。 如果我完成下一个任务目标,我最终将能够安装Linux: 如何在安装期间确定NMVe SSD的设备名称


仅供参考,目前Ubuntu 17.04的状态是(错误,错误,错误……):

 [ 2.772902] ath10k_pci 0000:05:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:05:00.0.bin failed with error -2 [ 2.772909] ath10k_pci 0000:05:00.0: Direct firmware load for ath10k/cal-pci-0000:05:00.0.bin failed with error -2 [ 2.773036] ath10k_pci 0000:05:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2 [ 2.773038] ath10k_pci 0000:05:00.0: could not fetch firmware file 'ath10k/QCA6174/hw3.0/firmware-5.bin': -2 [ 2.773892] ath10k_pci 0000:05:00.0: qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 1a56:1535 [ 2.773893] ath10k_pci 0000:05:00.0: kconfig debug 0 debugfs 1 tracing 1 dfs 0 testmode 0 [ 2.774309] ath10k_pci 0000:05:00.0: firmware ver WLAN.RM.2.0-00180-QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5 

linux-firmware包v 1.164.1

Disappointed Monkey GIF by Justin - Find & Share on GIPHY

请尝试更新的固件包。 有了正常工作的互联网连接,请打开一个终端并执行:

 wget http://mirrors.kernel.org/ubuntu/pool/main/l/linux-firmware/linux-firmware_1.161.1_all.deb sudo dpkg -i linux-firmware*.deb sudo modprobe -r ath10k_pci && sudo modprobe ath10k_pci 

您的无线现在应该正常工作。