USB 3.0 Asix AX88179无法在Ubuntu 13.10上运行
我从13.04升级到13.10，我从PPA安装了AX88179驱动程序。
当我升级USB 3.0到以太网转换器停止工作时，虽然它应该包含在从3.9开始的内核主线中。 它被系统识别但没有连接。
这是相关的详细lsusb输出：
Bus 004 Device 006: ID 0b95:1790 ASIX Electronics Corp. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 0 bMaxPacketSize0 9 idVendor 0x0b95 ASIX Electronics Corp. idProduct 0x1790 bcdDevice 1.00 iManufacturer 1 ASIX Elec. Corp. iProduct 2 AX88179 iSerial 3 00000000000001 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 57 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 124mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 0 iInterface 4 Network_Interface Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 11 bMaxBurst 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 3 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 Binary Object Store Descriptor: bLength 5 bDescriptorType 15 wTotalLength 22 bNumDeviceCaps 2 USB 2.0 Extension Device Capability: bLength 7 bDescriptorType 16 bDevCapabilityType 2 bmAttributes 0x00000002 Link Power Management (LPM) Supported SuperSpeed USB Device Capability: bLength 10 bDescriptorType 16 bDevCapabilityType 3 bmAttributes 0x00 wSpeedsSupported 0x000e Device can operate at Full Speed (12Mbps) Device can operate at High Speed (480Mbps) Device can operate at SuperSpeed (5Gbps) bFunctionalitySupport 1 Lowest fully-functional device speed is Full Speed (12Mbps) bU1DevExitLat 1 micro seconds bU2DevExitLat 101 micro seconds Device Status: 0x000c (Bus Powered) U1 Enabled U2 Enabled
与此问题不同， 该设备不再被识别为以太网设备。 这是dmseg的相关输出：
dmesg | grep ASIX [ 3.238120] usb 4-2: Manufacturer: ASIX Elec. Corp. [ 61.907446] usb 4-2: Manufacturer: ASIX Elec. Corp. [ 84.772115] usb 4-1: Manufacturer: ASIX Elec. Corp. [ 192.615236] usb 4-2: Manufacturer: ASIX Elec. Corp. [ 1146.200351] usb 4-2: Manufacturer: ASIX Elec. Corp. dmesg | grep AX88179 [ 3.238119] usb 4-2: Product: AX88179 [ 61.907444] usb 4-2: Product: AX88179 [ 84.772110] usb 4-1: Product: AX88179 [ 192.615231] usb 4-2: Product: AX88179 [ 1146.200346] usb 4-2: Product: AX88179
据我所知，升级后没有安装驱动程序。
除非Ubuntu进入睡眠模式，否则驱动程序工作正常。 从睡眠中恢复后，司机停止工作。
我找到的唯一解决方法是停用睡眠模式。
我安装了ppa：
add-apt-repository ppa:qji/ax88179 # since there is no source for soucy, replace it with raring: sed s/saucy/raring/g /etc/apt/sources.list.d/qji-ax88179-saucy.list>/etc/apt/sources.list.d/qji-ax88179-raring.list rm /etc/apt/sources.list.d/qji-ax88179-saucy.list aptitude update aptitude install ax88179 reboot
它工作了一次 ，这是第一次重启后的第一次工作。 从那时起，我在syslog中遇到了失败错误。 它可以在我的朋友的笔记本电脑上使用抛物线linux。 我会买另一个适配器;）